Posted in

What causes low BDV in transformer oil?

If you’ve ever worked with oil-type transformers, you know that transformer oil isn’t just a coolant—it’s a critical insulator and arc quencher that keeps your equipment running safely and reliably. One of the most important metrics we track here at our transformer supply company is the dielectric breakdown voltage (BDV) of that oil. For context, BDV measures the voltage required to cause an electrical breakdown (a spark or arc) in the oil. A healthy transformer oil should have a BDV of 30 kV or higher for standard distribution transformers, and up to 70 kV for large power units. But when that number drops—sometimes unexpectedly—it can signal a serious problem that puts your entire electrical system at risk. Oil-type Transformer

Over the 12 years we’ve been supplying oil-type transformers, we’ve helped hundreds of clients troubleshoot low BDV issues, from small commercial setups to industrial power grids. I’ve seen firsthand how a sudden BDV drop can lead to unplanned downtime, costly repairs, and even transformer failure. Today, I want to break down the most common causes of low BDV in transformer oil, explain why they matter, and share what we teach our clients to spot and fix them.

Let’s start with the basics: how BDV works. Transformer oil is a highly refined, hydrocarbon-based liquid designed to be nearly free of impurities. When there are no contaminants, electrical current can’t easily pass through it, so it insulates the transformer’s windings and core from each other and from the grounded tank. But even tiny amounts of certain impurities disrupt that balance, creating pathways for current to jump between parts. That’s exactly what causes low BDV.

The number one cause of low BDV we see is water contamination. It’s also the trickiest to address because water doesn’t just sit as a separate liquid in the oil—it can dissolve into the oil in small, invisible amounts. Even 10 parts per million (ppm) of water can lower BDV by 5 kV or more, and once it reaches 30 ppm, you’re looking at a BDV that’s often too low to meet industry standards.

Where does that water come from? There are two main sources. First, environmental moisture can seep into the transformer over time. Gaskets, seals, and even small cracks in the tank degrade after years of use, especially in high-humidity climates. Every time the transformer’s temperature rises and falls (a daily cycle in many operations), air is drawn into the tank, carrying water vapor. That vapor condenses into liquid water inside the transformer as temperatures drop. Second, water can enter during maintenance or installation. If you’re refilling oil or replacing parts and don’t properly dry the new oil or the components you’re installing, you’re introducing water straight into the system.

We once had a client at a food processing plant call us in a panic. Their 500 kVA distribution transformer had a BDV reading of 18 kV, just a few months after a routine maintenance check. When we inspected it, we found a small tear in the rubber gasket on the transformer’s conservator tank. The plant’s facility team had ignored a small leak for months, but the real issue was the water that had seeped in during the hot, humid summer. By the time we dried the oil and replaced the gasket, the BDV bounced back to 42 kV—and we helped them install a monthly moisture monitoring schedule to catch issues early.

Next up: solid particle contamination. Transformer oil is filtered to remove all solid particles, but over time, tiny particles from inside the transformer can break loose and accumulate in the oil. These include things like metal shavings from the windings or core, carbon from arcing, dust that gets drawn into the tank, and even fibers from gaskets or insulation materials.

The problem with solid particles is that they don’t just add physical mass to the oil—they create “bridges” between the transformer’s live parts. A metal shaving that’s 0.1 mm long might span the gap between two windings, creating a direct path for electrical current. Carbon particles, which form when small arcs occur inside the transformer, are highly conductive and can lower BDV dramatically. I’ve seen a case where a transformer with a minor internal arc (caused by a loose connection) had a BDV drop from 45 kV to 22 kV in just two weeks—all because of the carbon particles generated by that single small arc.

Solid particles also tend to settle at the bottom of the transformer tank, but when the unit vibrates (common in industrial settings with heavy machinery), they stir up and spread through the entire oil. Even small particles that are too tiny to see with the naked eye can disrupt the oil’s dielectric strength, because they act as “defects” that concentrate electrical field stress, making it easier for a breakdown to occur.

Another common culprit is dissolved gases. Transformer oil will break down over time, especially under electrical stress, into a mix of gases like hydrogen, methane, and ethane. These gases get dissolved in the oil, and when they form bubbles, they drastically reduce BDV. Bubbles act as insulators, but they’re less dense than oil, so they rise and accumulate near high-voltage parts. When voltage is applied, the bubble can ionize, creating a spark that spreads to surrounding parts.

Dissolved gases also come from external sources. If a transformer is exposed to extreme temperatures, or if there’s a fault inside (like a partial discharge), the oil breaks down faster, releasing more gas. Older transformers, especially those that have been in service for 20+ years, are more prone to this because their insulation degrades over time, leading to more gas production.

I once worked with a utility company that had a network of 20-year-old transformers in a rural area. Their BDV readings started dropping across the board, even though water and solid particles levels were normal. When we ran gas analysis tests, we found high levels of methane and ethane, which meant the oil was breaking down due to age and thermal stress from high load cycles during the summer. We recommended a full oil reclamation process to remove the dissolved gases, and most of those transformers’ BDV levels recovered by 10–15 kV.

Then there’s oxidation, a slower, more gradual cause of low BDV that often goes unnoticed until it’s advanced. Transformer oil is prone to oxidation when it’s exposed to oxygen, which happens any time there’s a void in the transformer’s tank (like in conservator-style transformers that have an air space above the oil). Oxidation creates sludge, acids, and resinous compounds that mix with the oil. These byproducts are conductive and act as solid contaminants, lowering BDV over months or years.

Oxidation is accelerated by high temperatures—transformers running at loads above their rating, or placed in areas with constant high ambient temperatures, will oxidize oil much faster. We’ve seen transformers in desert climates go from 40 kV BDV to 25 kV in just three years, all due to oxidation. The worst part is that oxidized oil isn’t just a BDV problem; it also eats away at insulation materials, shortening the transformer’s lifespan.

Finally, human error during maintenance is a far more common cause than many people realize. It’s not that maintenance teams are careless, but small oversights add up. For example, using unfiltered oil for top-ups—if you add oil that hasn’t been tested for BDV and impurities, you’re introducing contaminants right into the working oil. Or not properly degassing oil before filling it into a new transformer, leaving bubbles that lower BDV from day one. Even storing oil in un covered drums, which lets dust and moisture seep in, is a simple mistake that can cause BDV to drop.

I remember a new client who’d installed three of our 1000 kVA transformers for a new warehouse. After two months, their BDV reading was 21 kV. When we checked the oil samples, we found high levels of dust and moisture—turns out their team had ordered a batch of “new” oil from a local supplier, stored it outdoors in un sealed drums, and used it to top up the transformers after the first week of operation. We helped them replace the contaminated oil, filter the system, and install proper storage for spare oil, and their BDV returned to normal.

Now that we know what causes low BDV, what can you do about it? The good news is that most cases aren’t fatal if caught early. Regular testing is key—we recommend testing transformer oil for BDV at least once a year for transformers in service, and every six months for transformers in high-humidity, high-load, or coastal environments. Testing for moisture, solid particles, and dissolved gases alongside BDV gives you a full picture of the oil’s health, not just one metric.

If you do have low BDV, the fix depends on the cause. For water contamination, you can use vacuum dehydration to remove moisture from the oil—this is a common service we offer at our transformer supply company, and it’s usually enough to bring BDV back up. For solid particles, filtering the oil through a high-efficiency filter (often called a press filter) will remove most contaminants. If dissolved gases or oxidation are the issue, reclamation processes that remove gases and byproducts can restore BDV, though in severe cases, you might need to replace the oil entirely.

At the end of the day, low BDV isn’t just a number—it’s a warning sign that your transformer’s most critical insulation is compromised. Ignoring it can lead to costly repairs, unplanned downtime, and even safety hazards for your team.

If you’re noticing low BDV in your transformer oil, or if you’re due for routine testing or oil maintenance, our team is here to help. We supply high-quality oil-type transformers designed with BDV consistency in mind, and we offer oil testing, reclamation, and repair services to keep your equipment running smoothly. Reach out to our team to discuss your transformer needs and troubleshoot low BDV issues.

Low Voltage Distribution Box References

  1. American National Standards Institute (ANSI)/Institute of Electrical and Electronics Engineers (IEEE) C57.106, “Guide for the Operation and Maintenance of Liquid-Immersed Power Transformers”
  2. International Electrotechnical Commission (IEC) 60422, “Mineral Insulating Oils in Electrical Equipment – Guide for the Testing and Maintenance”
  3. Joint Oil Analysis Program (JOAP), “Transformer Oil Contamination and Dielectric Breakdown Voltage”
  4. National Electrical Manufacturers Association (NEMA) TR 1, “Liquid-Immersed Distribution, Power, and Regulating Transformers”

Kechang Electric Co., Ltd.
Kechang Electric Co., Ltd. is one of the leading oil-type transformer manufacturers and suppliers in China, also supports customized service. We warmly welcome you to wholesale high quality oil-type transformer made in China here from our factory. For pricelist, contact us now.
Address: North of Wenming Road, Xushui Economic Development Zone, Xushui District, Baoding City, Hebei Province, China
E-mail: frida@kechangelec.com
WebSite: https://www.kechangelec.com/