Posted in

can plastic injection molded parts be used outdoors

Hey everyone, it’s Jake here, co-owner of a plastic injection molded parts supplier—you know, the guy who gets 3 AM texts from customers panicking because their outdoor parts cracked after one winter storm, or their fence brackets turned milky green in a year. Today we’re tackling the question I get at least three times a week: can plastic injection molded parts actually be used outdoors? Spoiler alert: the answer isn’t a yes or a no—it’s “it depends on the plastic, the additives, and how you set it up.” Let’s break this down like we’re chatting over a post-work beer, no stuffy engineering jargon. Plastic Injection Molded Parts

First off, let’s get one thing straight: regular old plastic—like the cheap stuff you get from a random Amazon bin that says “polypropylene” but has no extra anything? That stuff is garbage outdoors. I saw a guy last month use our standard PP parts (the ones we make for indoor packaging) to build a bird feeder for his grandma. By month two, the sun turned it brittle enough to snap when a sparrow landed on it, and the rain turned it into a slimy mess that smelled like sour milk. That’s not our fault—that’s him not asking the right question, not using the right plastic.

Now, when do plastic injection molded parts work outdoors? Let’s talk about the good plastics, and the magic we add to make them tough. The three big ones we use for outdoor parts are HDPE, ABS, and polycarbonate—but wait, even those aren’t all created equal. Let’s start with HDPE: that’s the plastic used for milk jugs and cutting boards, right? The thick, flexible stuff. We can make HDPE outdoor parts that handle freezing temps, heavy rain, and even UV exposure for years—if we add UV stabilizers. UV is the big enemy here, not rain or cold. UV rays break down plastic’s molecular structure, making it fade, crack, and get brittle. Add UV stabilizers, and that HDPE part can last 10, 15 years easy. We made some parking lot light brackets last year for a city in Ohio—they’re in direct sun all day, snow and ice in winter, and they still look brand new two years later.

Next, polycarbonate. That’s the clear stuff used in airplane windows and phone screens, super strong and shatter-resistant. But plain polycarbonate scratches like crazy and turns yellow in the sun. We add a UV-resistant hard coat to polycarbonate outdoor parts, and suddenly it’s perfect for outdoor signs, greenhouse panels, or even playground equipment. I remember when we did the playground parts for a school in Texas—they were worried about parts breaking from kids climbing and sun turning them to mush. The polycarbonate with our custom UV hard coat? It’s been through 100+ degree Texas summers and zero cracks. Kids scuff it all the time, but it doesn’t yellow or break.

Then there’s ABS—wait, regular ABS is cheap, indoor only. But we make a weather-resistant ABS (we call it ABS-WR internally, don’t worry, not a fancy trade secret) that has extra UV and impact additives. We use that for things like outdoor electrical enclosures or fence post caps. Those hold up way better than metal sometimes—metal rusts, right? You have to paint metal, touch it up, replace it every few years. Our ABS-WR parts don’t rust, don’t need paint, and don’t get brittle in winter. I’ve seen a fence post cap we made in 2017 still on a house in Florida, where it rains almost every day and the sun is brutal. It looks almost the same as the day we delivered it.

Now, let’s talk about the mistakes I see people make all the time that ruin outdoor plastic parts. First, not accounting for temperature fluctuations. A lot of places get super hot in summer and freezing in winter—plastic expands and contracts with temperature changes. If you design a part that’s too rigid, with sharp corners, it’ll crack when it expands in the sun and contracts when it freezes. We always warn customers about that. Last year a customer sent us a design for a outdoor tool holder that had a 90-degree sharp corner. We told him, “Hey, that’ll crack in Minnesota winters.” He skipped our advice, made the part with our same material anyway, and three months later he’s emailing us pics of a cracked tool holder that fell off his garage. Should’ve listened.

Second, not sealing or venting parts if they’re going to hold air or water. If you make an outdoor electrical enclosure, and it traps water inside, that’s going to corrode the wiring, no matter what plastic you use. We add vent valves to those parts so air can circulate, but not water. And if you’re making a part that has moving parts, like a hinge on an outdoor gate, you have to lubricate it with a weather-resistant lubricant—regular WD-40 washes off in rain, so use something silicone-based that sticks. I saw a gate hinge made with our ABS-WR that the customer used regular oil on; by month six, the oil was gone, the hinge squeaked nonstop, and the pin rusted. We suggested switching to silicone lubricant, and it’s been fine ever since.

Third, buying cheap off-the-shelf plastic parts from a random supplier who doesn’t add the right additives. A lot of “outdoor” plastic parts you see online are just regular indoor plastic that they spray with a clear coat to make it look weatherproof. That clear coat peels off in a year, and the underlying plastic is garbage. We test every batch of our outdoor parts—we put them in UV chambers that simulate five years of sun in two weeks, freeze them at -40 degrees, blast them with salt water (for coastal customers), and check for cracks or fading. That’s why our parts cost a little more, but they don’t fall apart after a season.

Wait, what about coastal areas? That’s a whole other beast—salt air is way more corrosive than regular rain. We make a special grade of HDPE for coastal parts that has anti-corrosion additives, and we even add a thin layer of resin coating on top. We did some dock cleats for a marina in Florida last year, and the customer said they used metal cleats before, which rusted in two years. Our plastic cleats? No rust, no fading, still holding strong. That’s been two years too.

And let’s not forget about long-term testing. We have a test field behind our warehouse—just a big patch of ground where we stick all the prototype outdoor parts. Some we put there in 2015, and they’re still going. I walk out there every few months to check: some parts are faded a little, but not cracked, not brittle. One HDPE bracket we made for a solar panel mount is still holding up, even though it’s in full sun 12 hours a day. That’s the kind of real-world testing you can’t get from a lab.

Now, let’s address the myth that all plastic outdoor parts are worse than metal. Yeah, if you use the wrong plastic, sure. But if you use the right stuff? Plastic has advantages metal can’t touch. It’s lighter, so it’s easier to install—you don’t need a crew to lift a 50-pound metal bracket, one guy can put our plastic bracket on a solar panel in 10 minutes. It doesn’t conduct electricity, so if you’re making electrical enclosures, you don’t have to worry about shock hazards. And it’s cheaper than metal long-term, because you don’t have to paint or replace it.

I know a lot of people are skeptical, because they’ve had bad experiences with cheap plastic parts. That’s why I always tell customers to ask the supplier three questions: 1. What material are you using, and did you add UV stabilizers or other weather additives? 2. Have these parts been tested for outdoor use, specifically for the climate I’m in? 3. What’s the expected lifespan? If a supplier can’t answer those, run—don’t buy from them.

At our shop, we work with all kinds of customers: small businesses making outdoor furniture, cities making infrastructure parts, homeowners making custom projects. Last month we helped a guy build outdoor raised garden beds—we made the corner brackets out of our UV-stabilized HDPE, so he doesn’t have to treat the wood every year, and the brackets won’t rust. He texted me last week saying they survived a Michigan winter with no issues.

Wait, what about biodegradable plastic? A lot of people ask about that for outdoor parts. Biodegradable plastic is great for single-use stuff, like food packaging, but if you want a part that lasts 10 years outdoors? Skip it. Biodegradable plastic breaks down with moisture and microbes, so it’ll turn to mush in two years if it’s outside. We only use non-biodegradable, weather-resistant plastics for our outdoor parts, because that’s what actually holds up.

Another thing: design for disassembly if you’re planning to replace parts later. We design all our outdoor plastic parts with snap fits or stainless steel fasteners, so if a part does get damaged (rare, but it happens), you don’t have to tear apart the whole assembly to replace it. That’s a small detail, but it saves customers so much time and money.

Let’s wrap this up with a quick summary, because I know I rambled a bit: yes, plastic injection molded parts can absolutely be used outdoors, but only if you pick the right material, add the right additives, design for outdoor conditions (temperature, expansion, moisture), and work with a supplier who actually tests their parts for outdoor use. Skip the cheap generic stuff, ask the hard questions, and you’ll have parts that last way longer than metal, cost less, and don’t require constant maintenance.

If you’re working on an outdoor project—whether it’s a new deck, a dock, electrical enclosures, playground parts, whatever—and you’re not sure if plastic injection molded parts are right for you, hit me up. I don’t do pushy sales stuff, I just tell you what works. We can send you free samples, walk through design tweaks, and figure out exactly what you need to make your project last for years. No pressure, just good advice from a guy who’s been in this game for 12 years.

Wait, before I sign off, let me give a quick shoutout to all the customers who’ve learned from their mistakes. That Ohio guy who put regular PP on the bird feeder? He’s now one of our best customers, buying UV-stabilized HDPE parts for his landscaping business. You don’t know what works until you test it, right?

Plastic Mould References: 1. Plastic Injection Molding: Materials and Processes, Society of Plastics Engineers, 2021. 2. Outdoor Durability of Thermoplastics, American Society for Testing and Materials, 2019. 3. UV Stabilization of Polymers for Exterior Applications, Wiley, 2020.


Wuxi Santaizi Metal Products Co., Ltd.
As one of the most professional plastic injection molded parts manufacturers and suppliers in China, we warmly welcome you to buy high-grade plastic injection molded parts made in China here from our factory. All customized metal products are with high quality and competitive price. Contact us for pricelist.
Address: No. 23 Xufeng Road, Xushe Town, Yixing City, Wuxi City, Jiangsu Province, China
E-mail: Ksstzmj@163.com
WebSite: https://www.wuxisantaizi.com/