Posted in

Can a Velcro Disc be used for attaching blinds?

Hey everyone, let’s cut to the chase: if you’re tired of fumbling with drill bits, messy brackets, or those flimsy, one-size-fits-all blind hardware that falls off after a week, you’ve probably wondered if Velcro discs could work for attaching blinds. As a Velcro disc supplier who’s chatted with hundreds of homeowners, renters, and small contractors over the past few years, this question pops up all the time—and honestly, the answer isn’t a simple yes or no. It’s way more nuanced than that. Velcro Disc

First, let’s get on the same page about what we’re actually talking about here. Velcro discs aren’t just that scratchy stuff you used on your elementary school backpack. Most of the Velcro discs we supply (the good ones, anyway) are heavy-duty, pressure-sensitive adhesive (PSA) backed, specifically made for holding up medium-weight stuff—think wall art, fabric crafts, even small storage bins. They come in two pieces, right? The hook side (the scratchy part) and the loop side (the soft, fuzzy part), each with its own sticky pad. That’s the base of this whole “can I use them for blinds” question.

Now, blinds aren’t a small throw pillow. You’re dealing with a pane covering that’s, at minimum, a few pounds, and sometimes way more—those big, custom blackout blinds for a living room window? They can hit 10 or 15 pounds easy. So the first big question is: can Velcro discs hold that kind of weight without failing? The short answer is: sometimes, but only if you pick the right ones, and set them up correctly.

I’ve seen people do this wrong all the time. They grab the random, off-brand Velcro discs from the dollar store, slap one on each corner, and wonder why their blind falls down mid-shower (oops—bathroom blinds are a whole other headache because of humidity, but we’ll get to that). The heavy-duty Velcro discs we supply are rated for 5 to 10 pounds per pair (one hook, one loop) depending on the size—usually 1-inch discs are around 5 lbs, 2-inch are 10 lbs. So if you’ve got a 8-pound mini blind for a bedroom window, four 1-inch Velcro pairs would give you enough holding power. But if it’s a 12-pound living room blackout blind? You’re pushing it. Six 2-inch discs would be safer, because they spread the weight across more points instead of cramming it into just four corners.

That’s the science part, by the way. The adhesive on the back of the Velcro discs isn’t the same as craft Velcro. Our heavy-duty PSA is a rubber-acrylic blend that sticks to smooth, non-porous surfaces like painted drywall, vinyl window frames, or smooth wood. But if your wall is textured, or your blind headrail is made of a porous material like particleboard? That’s a problem. The adhesive can’t grip into the tiny nooks and crannies, so it’ll peel off over time. I’ve had a customer come to me last month with exactly that issue—they used dollar store Velcro on a textured bedroom wall, and half the discs fell off after two weeks. Fixing that just required switching to our porous-surface-friendly Velcro discs, which have a thicker adhesive that seeps into tiny gaps, and prepping the surface with rubbing alcohol first.

Speaking of surface prep—this is the part that 90% of people mess up, and it’s why Velcro discs fail more often than they should. You can’t just stick a Velcro disc on a dirty wall and expect it to hold. Dust, grease, even leftover paint flakes act as a barrier between the adhesive and the surface. I always tell customers to wipe the area with 70% isopropyl alcohol, let it dry for 10 full minutes, then press the Velcro discs on firmly. For extra hold, some people use a heat gun (on low heat) to activate the adhesive a little before pressing, but only if the surface can handle the heat—no vinyl frames, because that’ll melt.

Now, let’s talk about the pros of using Velcro discs for blinds, because there’s a lot to love here, especially if you’re a renter. I get it—drilling holes in your wall is a big no-no for most apartments, and even if you own your home, patching screw holes is a hassle when you move. Velcro discs leave zero holes. When you want to take the blinds down to clean them, you just peel them off, no tools needed, and the only mark left is a tiny bit of adhesive residue (which comes off with rubbing alcohol, easy). Also, installation is like 5 minutes, not 30 minutes with a drill and a level. I’ve installed a mini blind on a rental apartment window in that time—no noise, no mess, no landlord’s face crumpling when they see the wall.

But there are definitely cons, and we can’t ignore those, because that’s where people get into trouble. First, humidity. If you’re putting blinds in a bathroom or kitchen, where there’s constant steam? The adhesive on even the heavy-duty Velcro discs will break down over time. Steam seeps under the disc, loosening the bond, and the hook and loop parts get moldy. We do sell a water-resistant Velcro disc for that scenario, but even that isn’t meant for constant direct water. If it’s a bathroom, you’re still better off with tiny command strips, but if you have to use Velcro, the water-resistant ones work for a few months, not years.

Another con: alignment. Velcro discs are tiny, so if you don’t line them up perfectly, your blind will tilt. I’ve had a customer who tried this, and when they closed their bedroom blind, one side was an inch lower than the other because they stuck the bottom discs off by a quarter inch. It takes a little more care to line them up than traditional brackets, which have fixed slots. Pro tip here: use a level, mark light pencil lines where you want the discs, then stick each one on the line. Also, space them evenly—12 inches apart along the top rail, not just all clustered at the corners. That spreads the weight evenly so no single disc gets overloaded.

Wait, what about vertical blinds? Or sheer window treatments? I’ve had people ask me if Velcro works for those, too. For sheer curtains, definitely, but again, weight matters. Sheers are light, so 1-inch Velcro pairs spaced 18 inches apart work great. For vertical blinds, I’d say stick to the top rail—you can attach Velcro to the top of each slat and the window frame, but just make sure the slats are light, no heavy wooden verticals there.

Now, let’s be real—when should you use Velcro discs for blinds, and when should you skip them? If you’re a renter, want a no-hole install, have a window under 10 pounds, in a low-humidity room (bedroom, living room), Velcro is a great option. If you have a heavy blind (over 10 pounds), a bathroom blind, or want something that will stay put for 5+ years? Velcro might not be your first pick, but it’s still a viable option if you use the right heavy-duty discs and follow the surface prep steps.

I’ve also had a lot of questions about how long these discs last. We test our heavy-duty Velcro discs in-house—one pair stuck to a smooth drywall wall held 8 pounds of weight for over 18 months, no issues. The water-resistant ones, in a bathroom with daily steam, lasted around 8 months before the adhesive started to loosen. So it’s not forever, but it’s way longer than those $1 craft ones from the dollar store, which usually break after a month.

So let’s wrap this up: yes, a Velcro disc can be used for attaching blinds, but only if you do it right. Skip the cheap craft Velcro, get heavy-duty ones that match your blind’s weight, prep the surface properly, space the discs evenly, and avoid high-humidity areas if you can. It’s a great alternative to traditional brackets, especially for renters or anyone who doesn’t want to drill, but it’s not a one-size-fits-all solution.

Abrasive Sanding Paper If you’re testing this out for your own windows, feel free to reach out if you’ve got questions—we’re a Velcro disc supplier, so we know exactly which type works best for different blind weights and surfaces. No weird sales pitches, just honest advice from people who work with these discs every day. We can help you figure out how many pairs you need, which adhesive type fits your wall or blind frame, and even tips for getting that perfect alignment so your blinds don’t tilt. Whether you’re a homeowner tired of drilling holes, a renter looking for a temporary fix, or a small contractor doing a quick job, we’ve got you covered. Hit us up to chat through your specific setup, no pressure, just good info to make your blind install as easy as possible.

References

  1. ASTM International. (2020). Standard Test Method for Adhesion Strength of Pressure-Sensitive Adhesives to Rigid Substrates. ASTM D3330/D3330M-20.
  2. Velcro Industries. (2022). Heavy-Duty Fastener Performance Data: Shear and Peel Strength for Adhesive-Backed Hook and Loop Discs. Internal Product Testing Report.
  3. National Association of Home Builders. (2021). No-Drill Mounting Solutions for Residential Window Treatments. Housing Innovation Report.
  4. International Residential Code. (2020). Appendix E: Fastener Requirements for Non-Penetrating Wall and Window Attachments.

Zhenjiang Cutech Tools Co., Ltd.
Zhenjiang Cutech Tools Co., Ltd. is one of the most professional velcro disc manufacturers and suppliers in China, also supports customized service with low price. Please feel free to wholesale CE approved velcro disc made in China here from our factory. Welcome to contact us for pricelist and quotation.
Address: NO.66 Runxing Road, Runzhou Private Economy Development Zone, Zhenjiang, China.
E-mail: cutechtool@gmail.com
WebSite: https://www.cutech-tool.com/