{"id":3762,"date":"2026-11-21T12:57:02","date_gmt":"2026-11-21T04:57:02","guid":{"rendered":"http:\/\/www.andesparaglider.com\/blog\/?p=3762"},"modified":"2026-11-21T12:57:02","modified_gmt":"2026-11-21T04:57:02","slug":"what-are-the-common-defects-in-cnc-turning-4b2d-e3ef87","status":"publish","type":"post","link":"http:\/\/www.andesparaglider.com\/blog\/2026\/11\/21\/what-are-the-common-defects-in-cnc-turning-4b2d-e3ef87\/","title":{"rendered":"What are the common defects in CNC turning?"},"content":{"rendered":"<p>Alright, so let\u2019s break this down like we\u2019re chatting with a fellow metal fabricator or someone new to CNC turning\u2014no stuffy lab jargon, just real stuff we see every day at our shop. I\u2019m gonna keep it casual, use some common shop abbreviations, throw in a few examples from our projects, and make sure it\u2019s all focused on the common CNC turning defects we run into, since we\u2019re a CNC turning services provider. Let\u2019s start with how most folks call us saying their turned parts are off, and we track the same 7 or so defects that pop up way more often than we\u2019d like. <a href=\"https:\/\/www.multi-wins.com\/precision-cnc-machining\/cnc-turning-services\/\">CNC Turning Services<\/a><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/www.multi-wins.com\/uploads\/47606\/small\/aerospace-milled-partsfb054.jpg\"><\/p>\n<p>First, let\u2019s get one thing straight: CNC turning isn\u2019t just \u201cstick a bar in the lathe and press go.\u201d There\u2019s so many moving parts\u2014tool wear, machine setup, material quirks\u2014 and even a tiny misstep turns out a part that\u2019s scrap or needs rework, which no one has time for. We deal with this every single day, so I\u2019m not gonna regurgitate a textbook; I\u2019m gonna tell you what actually happens in our shop, plus the fixes we\u2019ve tested over 10 years.<\/p>\n<p>Let\u2019s start with the big one: Dimensional Deviation. This is the one that\u2019ll get a part rejected faster than anything. Dimensional deviation is when the finished measurement is off from the blueprint. For example, a client sends a print calling for a 0.500\u201d shaft diameter, and our CNC spits out 0.508\u201d\u2014that\u2019s way over the tolerance. Why does this happen? Most of the time it\u2019s tool wear, plain and simple. If a carbide insert is chipped or worn down 0.005\u201d after cutting 50 parts, the tool path is gonna be off every time. We also see this with machine backlash\u2014you know, when the lathe\u2019s lead screw has a little play, so it overshoots or undershoots on X-axis cuts. Another dumb one? Operator input error. Last month we had a new kid key in a 1.500\u201d length instead of 1.050\u201d for a client\u2019s valve part\u2014scrapped a whole bar of aluminum, oops. The fix here? We do a pre-run check on every job, measure the first part with our Mitutoyo micrometer, and we use tool life monitors that auto-stop the machine when an insert hits a set number of cuts. No more guessing.<\/p>\n<p>Next, Surface Roughness Non-Conformity. We get so many calls like, \u201cYour turned part feels like sandpaper on my gasket\u2014this isn\u2019t right.\u201d Surface roughness is measured in Ra (roughness average), right? Blueprints will say Ra 0.8 \u00b5m, but we\u2019ll get parts at Ra 3.2 \u00b5m that look like they\u2019ve been blasted. Why? Common culprits: too high a feed rate. If you\u2019re pushing the tool way too fast, it leaves those tiny chatter marks all over the surface. Or the tool nose radius is wrong\u2014using a 0.8mm nose insert when the blueprint calls for 0.4mm makes the surface look like it was filed by a beginner. Also, chatter\u2014those annoying high-frequency vibrations from the tool, machine, or part clamping. Last quarter we had a job for a bicycle crank that kept chattering because we were clamping a thin-walled tube in a regular 3-jaw chuck; we had to switch to a collet chuck and use a back support bar, and boom\u2014Ra 0.7, perfect. Pro tip: If the part feels \u201cgrainy\u201d when you run your finger over it, that\u2019s chatter. Fix it by slowing the feed rate down 10-15%, switching to a smaller nose radius insert, or making sure the part is super rigid during the cut.<\/p>\n<p>Third defect: Burr Formation. Everyone hates burrs\u2014those tiny sharp metal edges left on the part after turning. They\u2019re not just a nuisance; they can scratch mating parts, cut assembly hands, or cause leaks in hydraulic parts. Most burrs happen at the part\u2019s intersection\u2014like where a face cut meets an OD (outer diameter) cut, or the end of a shaft where the tool exits the material. Wait, but sometimes it\u2019s the material\u2019s fault? Free-machining steels (like 12L14) are supposed to chip easy, but if the tool is dull, they stick and leave burrs. We also see this when the tool\u2019s entry\/exit angles are off\u2014if the insert is set too high, it rips the material instead of cutting it cleanly. For example, a client needed medical device pins without any burrs because they go under skin; we switched to a sharp left-hand cut insert and used a deburr station with a nylon brush, and we got zero returns. Small burrs might get missed in visual checks, so we\u2019ve started adding a light deburr step to every high-tolerance job now.<\/p>\n<p>Fourth: Taper. Taper is when a turned part is wider on one end than the other\u2014like a cone instead of a straight cylinder. This is usually from machine issues. If the lathe\u2019s spindle isn\u2019t aligned with the Z-axis (that\u2019s the axis that moves along the length of the part), every cut will taper. Or, if the part is too long and flexible\u2014like a 12\u201d long 0.25\u201d diameter brass rod\u2014it will bend under the cutting force, so the tool cuts more on one side. Last year we had a job for a gun barrel blank that tapered 0.002\u201d over 8 inches; we fixed it by using a steady rest to support the midpoint of the rod, so it didn\u2019t flex. Another cause? Tool offset drift. If the machine\u2019s X-axis offset shifts mid-job, you\u2019ll get a taper because the tool is moving closer or farther from the spindle as it cuts along Z. We check spindle alignment monthly with a test bar and indicator, and we reset offsets every 20 parts for long runs.<\/p>\n<p>Fifth: Runout. Runout is when the part wobbles as it spins in the lathe, so the diameter changes around the circumference. There are two types: radial runout (the part moves side to side, making the diameter off) and axial runout (it rocks back and forth, messing up face cuts). Most of the time this is bad clamping. If you grip the part too hard, you can distort soft materials like aluminum, making it runout. Or, if the chuck jaws are worn\u2014if they\u2019re pitted or not aligned, they won\u2019t hold the part true. We had a client send us a stainless steel pump shaft that had 0.010\u201d runout, which caused the pump to leak; it turned out their original shop used jaws that were 10 years old. We replaced their jaws and re-ran the job, and the runout was down to 0.001\u201d, which is within tolerance. Another thing: if the part isn\u2019t centered in the spindle when you load it, that\u2019s user error, plain and simple. We do a quick \u201cspin check\u201d every time we load a part, using a dial indicator to make sure it\u2019s within 0.0005\u201d runout before cutting.<\/p>\n<p>Sixth: Tool Breakage. Tool breakage is the worst because it can ruin a whole bar of material and shut down the machine for a while. Most common causes: using the wrong tool material for the job. If you use a high-speed steel (HSS) insert to cut hardened tool steel, it\u2019s gonna snap\u2014HSS is too soft. You need carbide, or even ceramic for super hard materials. Or excessive cutting force from too deep a cut\u2014if you set a 0.5mm depth of cut when the insert can only handle 0.25mm, it\u2019ll break. Also, chip jamming\u2014when the metal chips don\u2019t flow away from the tool and get stuck between the tool and part, causing extra pressure. We use high-pressure coolant (100 PSI) to flush chips away, and we program chip-breaker grooves into our tool paths for stringy materials like 304 stainless, which makes chips break into small pieces instead of long strands that wrap around the tool. Last month we had a stringy 304 job that kept jamming; we switched to a different chip-breaker insert and didn\u2019t have a single broken tool the rest of the run.<\/p>\n<p>Seventh: Surface Cracking or Porosity. This is more common with certain materials\u2014like cast iron or titanium, or if you\u2019re working with weldments\u2014but it happens. Surface cracks are tiny fissures on the part\u2019s surface, and porosity is small holes, both of which weaken the part. Why? For materials like titanium, if you cut it too hot, the heat from the tool can cause micro-cracks because titanium is prone to work hardening. Or residual stress from prior machining\u2014if the bar was cut with a band saw before turning, it can have internal stress that causes cracks when you turn it. We fix this by using low-speed cuts for titanium, using sharp tools that don\u2019t generate extra heat, and stress-relieving the material before machining it. For cast iron, if you have porosity in the raw material, turning will bring those holes to the surface, so we always inspect raw material blanks first, not just when we\u2019re done machining.<\/p>\n<p>Now, let\u2019s be real\u2014no matter how careful you are, some defects will slip through, especially on complex jobs. That\u2019s why at our CNC turning services shop, we do three levels of inspection: first, in-process checks (measuring every 20 parts), then a first-article inspection (FAI) for new jobs, and finally a 100% visual and dimensional check for high-tolerance parts. We\u2019ve turned away so many jobs where the blueprint was impossible\u2014like calling for Ra 0.2 \u00b5m on a thin-walled part that would flex. We tell clients upfront if a design isn\u2019t feasible, instead of wasting time and material on a scrap part.<\/p>\n<p><img decoding=\"async\" src=\"https:\/\/www.multi-wins.com\/uploads\/47606\/small\/color-matched-plastic-parts085f7.jpg\"><\/p>\n<p>If you\u2019re dealing with CNC turning defects that are killing your production, or you need consistent, high-quality turned parts for your project, hit us up to chat. We work with all kinds of materials\u2014aluminum, stainless, steel, brass, titanium\u2014and handle runs from 10 parts to 10,000. No run-of-the-mill mistakes, just parts that meet your specs.<\/p>\n<p><a href=\"https:\/\/www.multi-wins.com\/vacuum-casting-services\/polyurethane-casting\/\">Polyurethane Casting<\/a> References:<\/p>\n<ol>\n<li>Modern Machine Shop. (2022). Common Defects in CNC Turning and How to Prevent Them.<\/li>\n<li>SMTA International. (2021). Surface Roughness Control in Precision Turning Processes.<\/li>\n<li>ASM International. (2020). Machining of Metals: Defect Mitigation Strategies for Turning Operations.<\/li>\n<\/ol>\n<hr>\n<p><a href=\"https:\/\/www.multi-wins.com\/\">Shenzhen Multi-Wins Precision Technology Co., Ltd.<\/a><br \/>As one of the most professional CNC turning manufacturers and suppliers in China, we have world-leading production equipment and strong manufacturing capabilities. Please feel free to buy customized CNC turning made in China here from our factory. Also, quotation is available.<br \/>Address: 1 Phase, Yi&#8217;an City Central Garden, Longfei Avenue, Longgang District, Shenzhen, GD, China. 518100<br \/>E-mail: info@multi-wins.com<br \/>WebSite: <a href=\"https:\/\/www.multi-wins.com\/\">https:\/\/www.multi-wins.com\/<\/a><\/p>\n","protected":false},"excerpt":{"rendered":"<p>Alright, so let\u2019s break this down like we\u2019re chatting with a fellow metal fabricator or someone &hellip; <a title=\"What are the common defects in CNC turning?\" class=\"hm-read-more\" href=\"http:\/\/www.andesparaglider.com\/blog\/2026\/11\/21\/what-are-the-common-defects-in-cnc-turning-4b2d-e3ef87\/\"><span class=\"screen-reader-text\">What are the common defects in CNC turning?<\/span>Read more<\/a><\/p>\n","protected":false},"author":240,"featured_media":3762,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[3725],"class_list":["post-3762","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-industry","tag-cnc-turning-services-493a-e42535"],"_links":{"self":[{"href":"http:\/\/www.andesparaglider.com\/blog\/wp-json\/wp\/v2\/posts\/3762","targetHints":{"allow":["GET"]}}],"collection":[{"href":"http:\/\/www.andesparaglider.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.andesparaglider.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.andesparaglider.com\/blog\/wp-json\/wp\/v2\/users\/240"}],"replies":[{"embeddable":true,"href":"http:\/\/www.andesparaglider.com\/blog\/wp-json\/wp\/v2\/comments?post=3762"}],"version-history":[{"count":0,"href":"http:\/\/www.andesparaglider.com\/blog\/wp-json\/wp\/v2\/posts\/3762\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"http:\/\/www.andesparaglider.com\/blog\/wp-json\/wp\/v2\/posts\/3762"}],"wp:attachment":[{"href":"http:\/\/www.andesparaglider.com\/blog\/wp-json\/wp\/v2\/media?parent=3762"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.andesparaglider.com\/blog\/wp-json\/wp\/v2\/categories?post=3762"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.andesparaglider.com\/blog\/wp-json\/wp\/v2\/tags?post=3762"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}